Leverage ratio

Spec sheet // Glossary // LEVERAGE RATIO
Glossary / L / Leverage ratio
Glossary · Regulatory reporting

Leverage ratio

Also called tier 1 leverage ratio, supplementary leverage ratio (SLR)

Definition

The leverage ratio measures a bank's Tier 1 capital against its total exposures, without any risk weighting. Under Basel III the minimum is 3%. It acts as a backstop to risk-based capital requirements, limiting how much a bank can borrow against its capital regardless of how low its models judge the risk of its assets.

TIER 1 CAPITALTOTAL EXPOSURES3% MINIMUM
Fig. 1 · Leverage ratio
Basel III leverage ratio framework · CRR leverage ratio requirement · PRA leverage ratio requirement
Key rulesBasel III leverage ratio framework · CRR leverage ratio requirement · PRA leverage ratio requirement · Enhanced supplementary leverage ratio final rule
Applies toEU credit institutions and investment firms subject to the CRR
RegionsGlobal · UK · EU · US
01

How it works

The numerator is Tier 1 capital. The denominator, the exposure measure, includes on-balance sheet assets, derivatives exposures, securities financing transactions and off-balance sheet items converted using credit conversion factors. Because no risk weights apply, a portfolio of low-risk government bonds needs the same capital per pound or dollar of exposure as riskier lending, which stops a bank building up excessive leverage through assets that models rate as safe.

Global systemically important banks hold an additional leverage ratio buffer set at half their risk-based surcharge. Jurisdictions apply the ratio differently: the UK applies 3.25% to its largest firms, and the US uses both a 4% Tier 1 leverage ratio and a supplementary leverage ratio for large banks. Banks report the ratio to supervisors and disclose it publicly in their Pillar 3 reports.

Step 1Measure capitalCalculate Tier 1 capital after regulatory deductions.
Step 2Measure exposuresAdd on-balance sheet, derivatives, SFT and off-balance sheet exposures.
Step 3DivideDivide Tier 1 capital by the total exposure measure.
Step 4CompareCheck the result against the minimum and any buffers.
Step 5ReportReport to the supervisor and disclose in Pillar 3.
02

The rules

Global · Minimum requirement 1 January 2018; G-SIB buffer 1 January 2023Basel III leverage ratio frameworkBasel Committee leverage ratio standard, Basel Framework chapters LEV10 to LEV40

Sets a 3% minimum Tier 1 leverage ratio and a buffer for G-SIBs equal to half their higher loss-absorbency requirement.

Internationally active banks, through national rules
EU · 28 June 2021; G-SII buffer 1 January 2023CRR leverage ratio requirementArticle 92(1)(d) and Article 92(1a) of Regulation (EU) No 575/2013, as amended by Regulation (EU) 2019/876 (CRR2)

Makes the 3% leverage ratio a binding requirement and adds a leverage ratio buffer for global systemically important institutions.

EU credit institutions and investment firms subject to the CRR
UK · 1 January 2026PRA leverage ratio requirementPRA Rulebook leverage ratio rules, as amended by PRA Policy Statement PS22/25

Requires in-scope firms to maintain a minimum leverage ratio of 3.25%, plus buffers; PS22/25 raised the retail deposits threshold from £50 billion.

UK banks, building societies and PRA-designated investment firms with retail deposits of £75 billion or more or non-UK assets of £10 billion or more
US · 1 April 2026Enhanced supplementary leverage ratio final ruleJoint Federal Reserve, OCC and FDIC final rule modifying the enhanced supplementary leverage ratio standards, 90 FR 55248

Sets the eSLR buffer at half the firm's method 1 G-SIB surcharge on top of the 3% supplementary leverage ratio, replacing the previous fixed buffers.

US G-SIB holding companies and their depository institution subsidiaries
03

Common questions

Why have a leverage ratio as well as risk-based capital?

Risk weights depend on models and assumptions that can understate risk. The leverage ratio is a simple, non-risk-based limit that caps total borrowing whatever the models say.

What is the difference between the US leverage ratio and the SLR?

The US Tier 1 leverage ratio uses on-balance sheet assets and applies to all banks at 4%. The supplementary leverage ratio adds off-balance sheet exposures and applies at 3% to large banks.

Does the UK leverage ratio apply to all banks?

No. The PRA's binding leverage ratio applies to firms above the retail deposits or non-UK assets thresholds. Smaller firms are not subject to the minimum.